Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser that works with CAN buses. It is discreet, does not use LED indicators or key fobs and is hidden in the wiring of the vehicle.
It also allows users to temporarily disable the system through Transport Mode for when they are renting their vehicle. This guide will walk you through the installation process of an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car against key hacking attacks, cloning attacks and relay attacks. The system is connected directly to the ECU of your vehicle and secured by a PIN code you set. It is not detected by thieves using diagnostic scanners and other modern methods. It isn't able to be disabled with circuit cuts.
The system is simple to use, but it is essential to have a an expert installation to ensure a secure and secure connection with your vehicle's ECU. A Thatcham-approved installer can help in the installation and programming of your Ghost system. They can also recommend a tracking or alarm system to complete the security package for your vehicle.
To prevent ghost car immobiliser of airbags or short circuits The installer must first remove your battery. Once this is done, the installer can safely begin work. Basic hand tools are helpful to make precise connections, while a multimeter can be used to test the electrical properties and safety. Insulation tape and cable tie are vital to secure connections and ensure that wiring is neat. Lastly, the user manual provides specific guidance tailored to your Ghost Immobiliser model.
It is essential to choose an area for grounding that is free of any paint or debris during installation. Installers should also ensure that the immobiliser's wires CAN H & the CAN L are connected to the correct ECU ports. These wires can be plugged in or soldered based on the model. A quality connector is recommended to ensure a sturdy and secure connection.
Transport Mode can be turned on by the customer after the installation is complete. This allows the vehicle to be utilized by valet parking companies or mechanics without needing to know the pin code. The customer has to press the icon for service on the dashboard five times over two seconds. After that, the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 is a highly efficient immobiliser that's TASSA verified and Thatcham approved. It's a smart option for those who regularly rents out their vehicles on platforms such as Turo. An immobiliser can reduce the cost of insurance, as it decreases the likelihood of theft.
Getting Started
If you are looking for a solution to safeguard your vehicle from theft You can't go wrong with an autowatch ghost immobiliser. The device protects your vehicle from being started if a criminal steals or copies the key. This is due to its advanced technology, which is designed to prevent the engine from starting without the correct PIN code is entered.
The device is connected to the vehicle's bus network CAN, allowing direct communication with the ECU. It uses the buttons on your dashboard and steering wheel to create a unique sequence which only you are aware of. This makes it impossible for anyone else to start your car. This is the ultimate security system that will safeguard your pride and joy, keeping its value intact should you decide to sell it in the future.
Installing a Ghost immobiliser is easy, but you must follow the instructions to avoid electrical problems and malfunctions of the system. First, you have to find and locate a permanent 12V power source as well as an adequate grounding point on the vehicle's chassis. Then, you'll be able to begin connecting the wires to the immobiliser. Be sure to use high-quality connectors and soldering techniques to ensure a strong connection. Also, ensure that you insulate the connections with heat shrink tubing and insulation tape to shield them from short circuits in electrical power and other problems.
After the wires are connected, you can plug in the battery and begin the engine to check whether the immobiliser works. After you've verified that everything is working correctly, you can install the immobiliser in a secure position inside the vehicle. Make sure to cover it well so that a thief cannot tamper with it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) which means it is a high-quality deterrent for car thieves. It is invulnerable to hacking and key cloning and cannot be disabled without a code. The device is also simple to use and can be put into a service valet mode so that your automobile is not activated when you take it in for servicing or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system designed to prevent vehicle theft. It communicates with your vehicle's ECU and directly connects to its CAN bus. Unlike other aftermarket systems that require the removal of circuit components the Ghost Immobiliser won't interfere with the factory settings of your vehicle.
The system is also inaccessible by thieves using scanners for diagnostics. The system doesn't transmit or receive radio frequency signals and instead uses CAN data for communication with your ECU. In addition, it doesn't need any modification to your car's existing key fobs.
Enter the sequence to disarm (either two or one buttons) and then switch on the ignition of your vehicle to activate the Ghost Immobiliser. ghost immobiliser and tracker will flash twice to confirm that you've entered the correct code. Now you can start your vehicle and drive safely.
Once installed, the Ghost Immobiliser guards your vehicle from hacking or key cloning, while preserving its value. In Transport Mode you can temporarily disable the Ghost Immobiliser if you need to give your car over for service or valet parking.
You'll need a constant power source (12V) and an earthing point to complete the installation of a Ghost immobiliser. Make sure both are properly insulated and can be touched. Cable ties are also suggested to secure the wires. This will reduce the risk of theft by potential thieves. To avoid making mistakes, make sure to double-check these points and mark them with labels or tape. ghost car immobiliser 's recommended to check every connection for signs of wear and tear. Connectors that are loose could cause malfunctions in the system, so make sure they're securely in place and properly insulated. Don't forget to test the Ghost Immobiliser after installation is completed. This will make sure that the unit is operating properly and that all connections and insulation are safe. Be sure to fix any issues immediately.
Testing
The Autowatch Ghost Immobiliser is a cutting-edge vehicle security system that seamlessly into your car's ECU to block unauthorised engine start. The innovative technology it uses protects your car against hacking, key cloning, and other typical tactics thieves employ to steal cars. The Ghost works in conjunction with existing tracking and alarm systems to provide the most effective security for your car. This system's unmatched features and discreet design make it a popular choice for car lovers and security-conscious motorists alike.
To ensure proper integration of the Ghost Immobiliser, it's important to follow every step of the installation process. The best place to start is to refer to the wiring diagram for your vehicle that will serve as a roadmap for locating and connecting the required wires. You'll then need to identify the power and grounding sources. Once you've found them, you will have to mark them so that they are easy to identify during installation. In addition, it is essential to use high-quality tools and materials. Basic hand tools will help you make precise connections. A multimeter can verify electrical values, and also ensure security. Cable ties and insulation tape will help keep all connections tidy and neat. Also, a user's guide will provide specific guidance tailored to your Ghost model.
It is crucial to test the system before installing it. Enter the PIN code into the system and then start the vehicle. This step will confirm the immobiliser works as intended and stop unauthorised vehicle starts. It's recommended to perform this procedure regularly as part of your routine inspections of the vehicle to ensure the system is operating properly.
Once the installation has been completed, you can start driving your car with confidence. The Ghost will keep your pride and joy safe from would-be thieves and ensure that nobody is able to escape with your car without the proper PIN code. The Ghost can be paired with an approved Thatcham tracker that detects any attempts at theft or tampering. This lets you track your car in the event that it's stolen.
The Ghost is compatible with a range of vehicles, including those made by all major manufacturers. Monty's Locksmith can assist you in securing your vehicle with this innovative device. Contact us today to find out more about our service and installation options. We are a TASSA registered installer, which assures us that we follow strict guidelines in the installation of our products. This ensures customers as well as insurance companies and law enforcement agencies that all installations are carried out safely and in a safe manner.